Two compounding problems, found by actually running it:
- pot_mass=1/water_mass=1 (~2kg) is far lighter than the mass the real
PID gains are tuned for (~30kg, matching the real recipes) - same
heater power swings a 2kg pot far faster than the gains expect,
causing massive overshoot (24 -> 37.5 instead of holding at 24).
Fixed by using the same realistic mass as sud_0010.json/sud_0020.json.
- The overshoot then needed a passive cooldown back down to the next
step's target - independent of any declared rate, governed by the
plant's L/C time constant (~350 min here), regardless of mass.
Removed the (now unnecessary, since the overshoot is gone) explicit
cooldown step too.
Predicted/actual duration drops from ~408 min to ~18-21 min - verified
both via components/sud_forecast.py's estimator and a live run against
the real server (reaches DONE, no controller chattering).
6 steps covering a plain ramp, a wait-for-confirm step, a plain hold,
a combined ramp+hold (up), a combined ramp+hold (down, exercises
COOL), and a final confirm - all small temperature deltas and 1-minute
holds so a full run finishes in well under a minute at typical warp
factors, for quickly cycling through Load/Start/Pause/Stop/restart
scenarios without waiting through a real brew.
A step's target temperature applies to the whole step (it's what a
ramp ramps to and what a hold then holds at), not just its ramp phase
- promote it from a nested "ramp": {"temp": ...} to a step-level
"temperature" field, defaulted like descr/grain_mass/etc. Updates all
consumers (Sud._build_step, SudTask, the GUI's forecast estimator,
demo_sud.py) and migrates sude/sud_0010.json and the README.
A step can now carry both 'ramp' and 'hold': it ramps to the target
temp, then holds there for the given duration, instead of needing two
separate schedule entries. Sud.temp_reached() switches such a step
from its ramp phase into its hold phase in place (re-firing the
step-changed callback so SudTask/demo_sud re-apply the hold's stirrer
settings); user_wait_for_continue still applies once the whole step -
both phases - is done.
Merges sud_0010.json's three ramp/hold pairs into combined steps.
Reformats it to json.dump()'s standard 2-space-free, ensure_ascii
output (from exercising the new upload feature against the real
schedule) and adds the matching downloaded copy. No schedule content
changed.
grain_mass and water_mass now live on each step (defaulted from
default.step) instead of being fixed for the whole brew, since both
change over a mash (malt going in, water boiling off).
Sud.derive_plant_params() takes them as arguments so it can be
recomputed per step; the demo re-applies the resulting M/C to both the
real plant and the controller's Smith-predictor model on every step
change via the new Pot.set_thermal_params()/
TempController.set_model_params().
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01CgR9tPaSzFkAwRAUyeaaCD
Steps now declare a "ramp" or "hold" key instead of a flat "type", and
unspecified fields (including nested stirrer settings) fall back to a
new top-level default.step structure. Stirrer config is now
interval_time/on_ratio, mapping directly onto AStirrer's cycle
time/duty cycle instead of separate on/off durations. Update
components/sud.py, tasks/sud.py, the Sud demo, sude/sud_0010.json, and
the README to match.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01CgR9tPaSzFkAwRAUyeaaCD
Add Sud.derive_plant_params(), which combines pot_mass/pot_material/
grain_mass/water_mass into a single lumped (mass, specific heat) pair
using approximate specific-heat constants for water, grain, and (by a
small material lookup table) the pot itself. demo_sud.py now builds
its plant_params from this instead of hardcoded C/M values, keeping
L/Td as the only manually-tuned plant parameters.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Now that duration is correctly read as seconds, bump the sample
schedule's hold steps from the placeholder 30-40s to more realistic
200-400s.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
sude/sud_0010.json moved from a list of combined ramp+hold+wait
"Rasten" with global stirrer constants to a flat "schedule" list of
explicit {"type": "heat"|"hold", ...} steps, each carrying its own
stirrer_speed/stirrer_time_on/stirrer_time_off and an optional
user_wait_for_continue (+ user_message).
- components/sud.py: Sud now tracks the current `step` instead of
`rast`; "heat" steps enter RAMPING (advanced externally via
temp_reached()), "hold" steps enter HOLDING and count down
`duration` minutes (0 if omitted). Either step type can pause in
WAIT_USER via user_wait_for_continue, surfaced through the new
user_message attribute.
- tasks/sud.py: SudTask only pushes theta_soll/heatrate_soll on
"heat" steps, converts each step's stirrer_time_on/off into a
duty_cycle/cycle_time on every step change (replacing the old
state-based RAMPING/HOLDING stirrer switching), and broadcasts
user_message changes. Stirring is now fully schedule-driven instead
of implicitly stopped on WAIT_USER/DONE (DONE still stops it, since
there's no step left to read settings from).
- scripts/demos/sud/demo_sud.py: mirrors the same step-driven wiring.
- README's Mash schedules section rewritten for the new schema.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
jens
